Showing posts with label driver. Show all posts
Showing posts with label driver. Show all posts
Monday, May 13, 2013
Stereo line driver circuit
This is the circuit diagram of a low cost stereo line driver is given here. The circuit consists of only two transistors and few passive components. Each BC 109C transistor is wired as an emitter follower for driving each channel. The voltage gain of the emitter follower is unity, but it has a high current gain and low output impedance, ideal for driving long cables. The output impedance is around 16 Ohms at 1KHz.Since voltage gain is unity power amplifiers must be used at the listening end in order to drive loud speakers.
Notes.
* Assemble the circuit on a general purpose PCB.
* The circuit can be powered from a 12V battery or 12V DC power supply.
* The inputs and outputs must be connected with respect to ground as shown in circuit.
* A power amplifier is needed at the listening end because the emitter follower has only unity voltage gain.
* The line driver circuit must be place close to the audio source.
Continue reading...
Notes.
* Assemble the circuit on a general purpose PCB.
* The circuit can be powered from a 12V battery or 12V DC power supply.
* The inputs and outputs must be connected with respect to ground as shown in circuit.
* A power amplifier is needed at the listening end because the emitter follower has only unity voltage gain.
* The line driver circuit must be place close to the audio source.
Friday, March 29, 2013
12 Volt DC Fluorescent Lamp Driver
A number of people have been unable to find the transformer needed for the Black Light project, so I looked around to see if I could find a fluorescent lamp driver that does not require any special components. I finally found one in Electronics Now. Here it is. It uses a normal 120 to 6V stepdown transformer in reverse to step 12V to about 350V to drive a lamp without the need to warm the filaments.
Parts:
C1 100uf 25V Electrolytic Capacitor
C2,C3 0.01uf 25V Ceramic Disc Capacitor
C4 0.01uf 1KV Ceramic Disc Capacitor
R1 1K 1/4W Resistor
R2 2.7K 1/4W Resistor
Q1 IRF510 MOSFET
U1 TLC555 Timer IC
T1 6V 300mA Transformer
LAMP 4W Fluorescent Lamp
MISC Board, Wire, Heatsink For Q1
Notes:
Continue reading...
Parts:C1 100uf 25V Electrolytic Capacitor
C2,C3 0.01uf 25V Ceramic Disc Capacitor
C4 0.01uf 1KV Ceramic Disc Capacitor
R1 1K 1/4W Resistor
R2 2.7K 1/4W Resistor
Q1 IRF510 MOSFET
U1 TLC555 Timer IC
T1 6V 300mA Transformer
LAMP 4W Fluorescent Lamp
MISC Board, Wire, Heatsink For Q1
Notes:
- Q1 must be installed on a heat sink.
- A 240V to 10V transformer will work better then the one in the parts list. The problem is that they are hard to find.
- This circuit can give a nasty (but not too dangerous) shock. Be careful around the output leads.
Wednesday, March 27, 2013
Stock Photoillustrationmechanic Screw Driver Toolbox
What Does An Aircraft Mechanic Do.
Type D 1 Mechanics Sheerling Jacket Jacket Aircraft Mechanic S Type D.
Type D 1 Mechanics Sheerling Jacket Jacket Aircraft Mechanic S Type D.
Aircraft Mechanic.
Aircraft Mechanic Career Guide Eskwelahan Com Philippine Online.
Aircraft Mechanics And Avionics Technicians Must Be Certified By The.
Men Aircraft Vehicle And Mobile Equipment Mechanics Forbes Com.
Aircraft Mechanic Job Description And Salary Information.
Warhawk Of The Far East.
Stock Photo Illustration Of A Mechanic With Screw Driver And Toolbox.
Labels:
driver,
photoillustrationmechanic,
screw,
stock,
toolbox
Wednesday, March 20, 2013
LOW NOISE WHITE LED DRIVER SYSTEM ELECTRONIC DIAGRAM

LOW NOISE WHITE LED DRIVER SYSTEM ELECTRONIC DIAGRAM
The LM3570 evaluation board has a chip enable pin (active high logic) as well as a PWM (active high logic) pin which allows current sources to be turned on and off without completely disabling the part..The LM3570 is capable of supplying up to 80mA of current split between the regulated current sources and VOUT. The LM3570 comes in National’s LLP-14 package.
Subscribe to:
Posts (Atom)